| 代码 |
英文解释 |
中文解释 |
| E 113 |
|
无定影器 |
| E 510 |
|
激光器棱镜电机故障 |
| E 511 |
|
电机 1 故障 |
| E 512 |
|
P/H 电机故障 |
| E 513 |
|
NVRAM 故障 |
| E 516 |
|
双面单元故障(通信故障) |
| E 517 |
|
可选纸盒故障 |
| E 520 |
|
二次转印故障(Advance) |
| E 521 |
2nd BTR error FIP-1.27 “2ND BTR Error” (p.220) |
二次转印故障 |
| E 523 |
PCDC malfunction FIP-1.25 “PCDC Error” (p.219) |
PCDC 故障 |
| E 524 |
Toner density error (low density) FIP-1.24 “Low Density Error” (p.218) |
碳粉浓度过低 |
| E 525 |
Toner density error (high density) FIP-1.23 “High Density Error” (p.217) |
碳粉浓度过高 |
| E 526 |
Soiled ADC sensor FIP-1.22 “ADC Sensor Soiled” (p.217) |
ADC 传感器脏 |
| E 527 |
Deve home position sensor error |
显影原位传感器故障 |
| E 530 |
Environment (humidity) sensor error FIP-1.31 “Environment (Humidity) Sensor Related Error” (p.224) |
环境(湿度)传感器故障 |
| E 531 |
PR motor error FIP-1.19 “P/R MOT&DRV ASSY Related Error” (p.214) |
PR 电机故障 |
| E 532 |
P/H motor 2 error • FIP-1.15 “P/H MOTOR ASSY Related Error” (p.210) |
P/H 电机2 故障 |
| E 533 |
Temperature sensor error FIP-1.29 “FUSER Overheat Error” (p.222) |
温度传感器故障 |
| E 534 |
Fuser Unit error (low temperature) FIP-1.30 “FUSER Warm-up Error” / “Heater Error”/ “FUSER Low Temperature Error” (p.223) |
定影器故障(低温) |
| E 535 |
Fuser Unit error (Heater lamp) FIP-1.30 “FUSER Warm-up Error” / “Heater Error”/ “FUSER Low Temperature Error” (p.223) |
定影器故障(灯管) |
| E 536 |
Fuser Unit error (time out) FIP-1.30 “FUSER Warm-up Error” / “Heater Error”/ “FUSER Low Temperature Error” (p.223) |
定影器故障(超时) |
| E 537 |
Fuser Unit error (over heat) FIP-1.29 “FUSER Overheat Error” (p.222) |
定影器故障(过热) |
| E 543 |
Rear fan error FIP-1.34 “DEVE. FAN Error” (p.225) Table 3-3. Service Call Errors (Engine Related) (continued) ErrorCode ggg Explanation Refer to |
后部风扇故障 |
| E 544 |
Fuser Unit fan 2 error FIP-1.33 “FUSER CHUTE FAN Error” (p.225) |
定影器风扇2故障 |
| E 545 |
Fuser Unit fan 1 error FIP-1.32 “FUSER FAN-1 Error” (p.224) |
定影器风扇1故障 |
| E 546 |
Duplex Unit motor error *3 |
双面单元电机故障 |
| E 547 |
2/1 Optional Cassette Unit Feeder Motor error *3 |
可选纸盒进纸电机故障 |
| E 620 |
K Development end FIP-1.35 “Life Error/Over/Warning” (p.226) |
K 显影器寿命已到 |
| E 621 |
C Development end FIP-1.35 “Life Error/Over/Warning” (p.226) |
C 显影器寿命已到 |
| E 622 |
M Development end FIP-1.35 “Life Error/Over/Warning” (p.226) |
M 显影器寿命已到 |
| E 623 |
Y Development end FIP-1.35 “Life Error/Over/Warning” (p.226) |
Y 显影器寿命已到 |
| E 624 |
IBT end FIP-1.35 “Life Error/Over/Warning” (p.226) |
转印皮带寿命已到 |
| E 626 |
2nd BTR end FIP-1.35 “Life Error/Over/Warning” (p.226) |
二次转印组件寿命已到 |
| E 627 |
IBT Cleaner end FIP-1.35 “Life Error/Over/Warning” (p.226) |
皮带刮板寿命已到 |
| E 830 |
2 Optional Cassette Unit LC3 error (lift up) *3 |
可选大容量纸盒LC3故障 |
| E 831 |
1/2 Optional Cassette Unit LC2 error (lift up) *3 |
可选纸盒LC2故障 |
| E 832 |
MP Tray error (lift down) FIP-1.44 “MSI Tray Malfunction (Lift Down)” (p.232) |
多功能纸盒故障(下降) |
| E 833 |
MP Tray error (lift up) FIP-1.43 “MSI Tray Malfunction (Lift Up)” (p.231) |
多功能纸盒故障(抬起) |
| E 998 |
Engine communication error FIP-1.47 Engine Communication Error (p.234) Table 3-3. Service Call Errors (Engine Related) (continued) Error Code ggg Explanation Refer to |
引擎通信错 |
